Spa Treatment instructions

**How Do I Use Clarity for Spas Chemical Alternative?**

First, we Crystal Clean your spa to remove chemical residues, hard water deposits, corrosion and other contaminants hidden deep inside the plumbing of your spa that cause irritation, cloudy water, improper operation or pH imbalance. Crystal Clean is a strong, easy to use citrus based cleaner that won't hurt you or any of the components of your spa. Add 4 ounces for every 100 gallons of water and run your spa three to four times a day for 4 to 7 days. The spa cleans itself! Drain the spa once it’s clean, and you’re ready to start enjoying a Clarity for Spas.

Our START UP Kit includes one 16oz bottle of Clarity for Spas, 20 ounces of Crystal Clean, and complete instructions (a $39.90 value). That’s everything you’ll need for all spas up to 500 gallons.

A START UP Kit is only $ 34.95

Additional bottles of Clarity for Spas are $ 19.95

Save over $20 when you reorder, and ask for our 4-pack special for $69.95

Call 800-860-2477 to Order

For new spas.

NOTE: New spas are "wet tested" at the factory to make sure that everything works correctly, and to guarantee no leaks. Then they are drained and wrapped in protective plastic. Eventually they are shipped to the dealer or new owner. Because these spas have been wet, algae and mold may begin to grow inside the plumbing and filter in the dark, moist environment. The same is true for the seldom-used garden hose that you will be using to fill this new spa with. The first time you fill your new spa, or anytime the spa has been drained and left empty for more than three weeks health officials recommend flushing the spa thoroughly with an 80ppm chlorine solution, or soaking with a 20ppm solution for nine hours or longer. In addition, you should soak the filter for 90 minutes or longer in a solution of 1 part household bleach to 7 parts water.

When you get a new spa, you will want to use it a lot, and of course you want the water to stay crystal clear. But new spas may have manufacturing residues of silicon, Teflon, waxes and other chemicals that slowly wash out and cause cloudy water for many months. Chlorine will bleach these residues, keeping the water clear during this time. And so, for new spa owners we suggest the use of dichlor, (not bromine), per the chlorine manufacturer's recommendations for the first 30 days. Then Crystal Clean and drain.

If you do not want to soak in highly chlorinated water, then fill your spa and add Clarity for Spas according to label instructions. You may notice a slight haze for awhile as the manufacturing residues wash off into the water. We recommend you 'shock' occasionally with non-chlorine shock, hydrogen peroxide, or chlorine, then Crystal Clean after four to six weeks of use.

It's your choice. Complete instructions are in our starter kits.

800-860-2477

IF YOU NOW USE BIGUANIDE (BaquaSpaâ ).

Drain your spa and refill with fresh water to eliminate the Biguanide in the water. Crystal Clean the spa and soak the filter in a concentrated solution of Crystal Clean. Add Clarity for Spas to the fresh water. You may need to 'shock' the water with non-chlorine shock, or hydrogen peroxide in the next few weeks to maintain clarity.

IF YOU NOW USE CHLORINE OR BROMINE.

Take out the filter and toss the bromine floater, if used. Rinse and replace your filter so that the water treated with Crystal Clean will clean it thoroughly. Turn on all the jets and slowly add Crystal Clean to the skimmer area of your spa. The longer you circulate the water, the better the cleaning job. The contaminants that are in your spa will cause the water to get cloudy and may cause foam and scum to rise to the surface. Scoop away this foam while purging, and dispose of it. Crystal Clean your spa for 6 days, until thoroughly clean.

Once your spa is clean, fill with fresh water and shock the new water with 15ppm of chlorine. This should remove any residual chloramines, tannins or algae.

You may use your spa as soon as it is hot enough, though the chlorine level will still be quite high.

If your water is high in iron, copper, calcium or other scale causing metals: Add 1 to 2 ounces of Crystal Clean to every 100 gallons of water on the third day, to sequester these metals and prevent any problems with staining or scaling.

Heat the water to at least 80° F, and wait until the chlorine level is below 2ppm before adding Clarity for Spas. You will notice that Clarity for Spas is a thick liquid, and does not immediately dissolve into the water. Take out the filter and circulate with the air off for 15 minutes or more to mix the Clarity for Spas into the water, but don't put the filter back in for 4 hours. This gives the Clarity for Spas time to fully dissolve into the new water, rather than getting stuck in the filter.

One bottle of Clarity for Spas will keep your water looking and feeling great for one to two months with average use. If you use your spa 3 to 5 days a week for twenty minutes each time, we consider that average use. With more use by more people or for longer times you will have to add a bottle more often. If you use your spa daily, you will add a bottle every 4 to 5 weeks. If you don't use your spa for long periods of time, you may find that the water stays nice and clear for 3 to 4 months. When you haven’t used your spa for a long time, you need to add a new bottle of Clarity for Spas before use to recondition the water.

The final consideration is the size of your spa. One bottle of Clarity for Spas will treat up to 500 gallons, so larger spas will need to start with two bottles or more. Large swim spas will need a bottle of Clarity for Spas added every one to two months even when not used a lot. Smaller spas (under 200 gal.) can be a bit more difficult to maintain, especially under heavy use. Best results come from adding one full bottle after filling with fresh water, then adding another ½ bottle every three to four weeks, and depending upon use. Also, small spas should be drained more often. And remember to remove (and clean) the filter whenever you are adding a bottle.

No testing is required, as Clarity for Spas has no effect on pH or alkalinity.

And there is no need to drain the water as long as it stays clear and fresh, which can be up to a year. We do recommend that you drain every 6 months, (just because), and use Crystal Clean just before you drain, to keep your spa as clean as can be. A clean spa uses less energy to heat the water, runs smoother and lasts longer.

ENJOY!

Call 800-860-2477 to Order

NORMAL MAINTENANCE

Circulate twice daily on high, with lots of air induction for 15 minutes to an hour. Longer running times reduce the product life.

Add 1 full bottle of Clarity for Spas EVERY TWO MONTHS:

Clean filter with high-pressure nozzle when adding a bottle of Clarity for Spas. If you clean the filter too often you are washing away the Clarity for Spas and leaving your spa water unconditioned. Once a year, or as needed soak the filter(s) in a bucket of water with 1/2oz Crystal Clean per gallon of water. Do not use other filter cleaners as most will cause extensive foaming for several days.
Check pH and balance if necessary. Your pH can be between 6.8 and 8.4. Most city water has had the pH and alkalinity properly balanced before distribution. The Clarity for Spas can tolerate a much greater pH range and still maintain water quality. A higher pH is healthier for your skin. You can raise the pH by adding baking soda to your spa, 1 ounce at a time. To lower the pH use Crystal Clean. DO NOT add more than 8 ounces at a time - you want to lower the pH slowly. Wait at least 4 hours after adding any chemical before testing to see what effect it has had on the water.
Spas of 200 gallons or less should add one full bottle of Clarity for Spas to fresh water, then replenish with ½ bottle every 3 to four weeks, depending on use.

EVERY 6 MONTHS:

Add Crystal Clean 6 days before draining to keep the spa nice and clean. Soak filter in bucket of water with ½ oz Crystal Clean per gallon of water. With Clarity for Spas there is no build-up of toxic, corrosive chemicals in your water to worry about, so water changes are needed much less often than the one to four months required with other systems.

800-860-2477

THINGS TO KNOW

Alkalinity: Alkalinity can be anywhere between 60 and 280. Raise alkalinity with baking soda or Alkalinity Increaser, lower with Muriatic Acid or Easy Acid, available at a pool supply.

Metal Gonâ : Not needed. If your local water is very high in dissolved metals, add 1 to 3 ounces of Crystal Clean to every 100 gallons of new water to sequester these metals and prevent any problems with staining or scaling.

Defenderâ : Because you’re not adding tablets or granules to your water, you normally will not need this product. If sandy crystals begin to form, use Crystal Clean to cure and prevent the problem, according to our instructions.

Foam: Do not use 'Foam Down' type products. Lingering clumps of foam mean it's time to add another bottle of Clarity for Spas. If the foam is excessive, scoop it off and dispose of it to eliminate the cause of the foam. If it doesn't go away in a day or two, then Crystal Clean and drain the spa.

Clarifiers: Do not use a clarifier, as Clarity for Spas is a clarifier itself. Other clarifiers may cause foam and some may even bond with the Clarity for Spas and cause it to be filtered out of your water.

Ozone, non-chlorine shock and hydrogen peroxide: You should use these oxidizers under heavy use conditions. These are excellent products that help clear the water, though constant shocking will shorten the effective life of the Clarity for Spas.

ONE BOTTLE LASTS TWO MONTHS, or about 20 hours of use, counting each week that has gone by since adding your last bottle as 1 hour of use. With frequent use you will need to add Clarity for Spas more often. Surface scum or foam are indicators that it's time to add a new bottle.

IF YOU HAVE ANY QUESTIONS ABOUT OUR PRODUCTS, PLEASE CALL US:

800-860-2477

Spa Chemicals and Your Health

Home

INSTRUCTIONS for Clarity for Spas

BACTERIA TOTAL COUNT TEST

Only $9.95 per test add to cart

Fast, simple, microbiological analyses of most any water.

CAUTION: Test membrane is highly susceptible to outside contamination. DO NOT open tester until ready to take water sample. DO NOT touch, breathe on, or otherwise contaminate test pad. Test only the water.

NOTE: Samples containing residual chlorine must be neutralized with sodium thiosulfate (0.1 mL of 10% solution per 4oz. of sample) prior to testing.

INSTRUCTIONS:

Remove the sampler from its plastic bag and write date and time on the case with indelible marker.
Remove the ‘paddle’ from the case, being careful not to breathe on, touch, or contaminate the membrane.
Invert case so that opening is face down and submerge to a depth of 6" or more at arms length into water.
Turn case over and allow to fill with water sample.
Remove case from water and tip, allowing excess water to run out, until full to upper line.
Insert paddle firmly into case, and carefully lay the unit on a flat surface with membrane (gray side) facing down. Make certain the membrane is uniformly wetted, and while in this position the unit should not be agitated.
Allow 30 seconds, no more and no less, for water sample to soak into membrane.
Remove the paddle and, with a firm snap of the wrist, shake off the excess liquid.
Empty the case and reinsert the paddle. The paddle should be seated firmly in the case to form an airtight seal.
Incubate by placing the sampler, membrane side down, on a flat surface in an area where the temperature is a constant 95º F. (Under the spa cover is normally a good place)
DO NOT OPEN SAMPLER. After 24 hours, count the number of individual blue dots on the sample paddle. These are coliform colonies. See Coliform Count below.
Continue to incubate the sampler, face down, for an additional 48 hours at 77-95º F.
Count all of the individual dots on the sample paddle. This will give you the Total Count.

800-860-2477

INTERPRETING TEST RESULTS

Coliform Count: If the number of coliform colonies (blue dots) on the entire paddle is more than 3, sterilize the water immediately. To do this, raise the active chlorine level to 20ppm and keep it there for 9 hours. Adjust pH to between 7.2 and 7.4. Soak filter in a solution of 1 part household bleach and 9 parts water.

Total Count: If there are up to 7 dots per square (not the whole paddle) on average, this is considered to be normal for pools and spas. It would take around 300 dots per square to cause an infection. This many colonies would make the entire paddle look like orange peel. High bacteria levels may indicate a need for an increase in sanitation, depending upon the type of contaminant present. Test before using the pool, allowing a day or so since the last use.

The individual dots (colonies) are made up of the following:

Bacteria which are usually glistening and transparent
Yeast which usually has a satiny, opaque, white color
Mold which appears with spidery-like arms
Algae, fungus or other plant growth, which can be green, gray or cream color.

Test your water then decide for yourself which treatment system is the best for you. Adequate, rather than extreme levels of sanitation assure you an environment that is not only safe, but also more comfortable and less worrisome.

100% SATISFACTION GUARANTEED